PN00110-24C - Brushless (BLDC) 24v Motor Driver Speed Controller 15A - Makermotor

4.8 (345) · € 43.00 · Auf Lager

Makermotor provides variable speed gear motors and single speed motors for applications such as bbq rotissier motor, experimental motor for lab, conveyor motor system, and welding turn table. Our products cover speed range from low speed gear motors to high rpm variable speed motors.
Specifications: Shut-down at 6000 RPM Soft-start mode E-stop control 0-5vdc analog control PWM digital control (minimum 7kHz up to 16kHz) Reversible control Rated at 22-30 vdc Continuous duty at 15 amps DC Power supply friendly Fully enclosed Wiring Instructions: Connect 3 phase wires (A, B, and C) to the 3 phase wires of your BLDC motor. If you have a sensored BLDC motor, leave the hall sensor wires. This controller does not require hall sensors. Connect thick red wire +24VDC (IN) to the positive terminal of your power supply or battery. Connect thick black wire 0V (GND) to the negative terminal of your power supply or battery. Make sure you connect your controller in the correct polarity. Reverse polarity will damage this controller. To connect to a pot (potentiometer) for a manual control: Connect thin black wire 0V (GND) to your pot's GND. Connect thin yellow wire SIGNAL (IN) to your pot's Output. Connect thin red wire 5VDC to your pot's +Vcc. Introduce an on/off toggle switch between thin black wire and thin white wire REVERSE. This will let you switch between CW and CCW rotations. Introduce an on/off toggle switch between thin black wire and thin blue wire STOP. This will let you switch between stop and run functions. Introduce an on/off toggle switch between thin black wire and thin green wire SOFT START. This will let you enable/disable the soft-start feature. Soft start's ramp-up time is about 3 seconds. To connect to a microcontroller: Logic voltage has to be 5vdc. PWM needs to output at least at frequency of 7 kHz. Maximum frequency is 16 kHz. Connect your PWM signal to the thin yellow wire SIGNAL (IN). Switch signals between low (0vdc) and high (5vdc) to the thin white wire REVERSE for CW and CCW rotations. Switch signals between low (0vdc) and high (5vdc) to the thin blue wire STOP for stop (low) and run (high) functions. Switch signals between low (0vdc) and high (5vdc) to the thin green wire SOFT START for enabling (low) and disabling (high) its feature. Soft start's ramp-up time is about 3 seconds. To run as a single speed motor: Connect thin red wire to thin yellow wire. Connect thin green wire to thin black wire to enable the soft-start feature (recommended). Introduce an on/off toggle switch between thin black wire and thin white wire REVERSE. This will let you switch between CW and CCW rotations.

Source The Right Wholesale brushless motor speed controller

Brushless Controller, Aluminium Alloy E-Bike Brushless Controller for Steady Speed, Sensitive Control of Braking Direction Changes (24V, 250W) : Sports & Outdoors

Position Limit high current 12V 24V 36V 48V 100A Brushed Dc Motor Controller 12v 100A dc motor speed controller - Buy 24V dc motor speed controller, motor controller dc, speed controller Product

12V,24V,36V,5A,10A,15A 700W brushless DC motor driver,Hall sensor,brushless DC motor speed controller

15A 24 Volt Sensorless BLDC Driver Board Speed Control

500W Brushless DC Motor Driver , Hall Effect 24 Volt DC Motor Speed Controller

Brushless Motor Controller

24 Volt Electric Scooter Speed Controllers

Motor Drivers and Controllers - Page 2 - Makermotor

PN00211-40-24V - BLDC Gear Motor 40RPM 24V High Torque Variable Speed Integral Controller - Makermotor

24 Volt Electric Scooter Speed Controllers

High-quality Materials-This brushless controller is made of aluminum alloy, the shell is sturdy and durable. Circuit Protection-The brushless controller housing is made of aluminum alloy with groove design. Due to its good heat dissipation function, it can protect the internal circuit and avoid thermal overload. Sensitive Control-The electric bicycle controller is a brushless motor controller, which can provide stable speed and sensitive control of braking and direction changes.

Brushless Controller, Aluminium Alloy E-Bike Brushless Controller for Steady Speed, Sensitive Control of Braking Direction Changes

Buy 12V 24V 36V48V Brushless DC Motor Speed Controller with Hall Sensor 10/50DPW15BL bldc motor driver for Ebike scooter BBQ machine at Aliexpress for